
What the grade number actually means
The number after the letters HT is the minimum tensile strength in megapascals, so HT250 means the iron is expected to pull at least 250 MPa before it breaks. That single figure hides a lot: hardness, graphite shape, phosphorus content and how the iron was melted all move with the grade. A buyer who only quotes the number and ignores the rest will be surprised by how the casting machines and how it behaves in service.
HT200 for light frames and covers
At the low end, HT200 is the workhorse for covers, housings, brackets and other parts that mostly hold a shape rather than carry a load. It machines easily, pours cleanly in thin sections and keeps cost down. A supplier will often suggest HT200 for any component where stiffness matters more than raw strength, which is most of the non-critical cast iron parts on a machine.
HT250 the default for beds and columns
HT250 is the grade most foundries reach for when a part has to be both stable and reasonably strong. Machine beds, columns, bases and spindle housings are routinely poured in HT250 because it balances damping, machinability and load-carrying ability. If a drawing does not specify a grade, there is a good chance the manufacturer will default to HT250 unless the loads say otherwise.
HT300 where stiffness and load matter
When a casting carries heavy clamping forces, overhangs or high-speed spindle reaction, HT300 earns its place. It is harder to machine and a little more prone to chill, but the extra strength lets designers make walls thinner and structures lighter without losing rigidity. Heavy machining centers and precision grinders lean on HT300 for the parts that define the machine's accuracy.
Strength versus machinability trade-off
Here is the uncomfortable truth: the stronger the gray iron, the harder it is on tooling. HT300 will blunt inserts faster than HT200 and complain more about interrupted cuts. The trick is to specify the lowest grade that meets the structural need, not the highest one the sales engineer is happy to pour. A foundry that understands your application will push you down a grade when it is safe to.
How foundries keep grade consistent
A manufacturer controls grade with charge chemistry, melting practice and ladle treatment, then proves it with a coupon poured from the same heat. Buyers should ask for that test bar result tied to a heat number, because a certificate that says HT250 means little without the bar it came from. Consistency between heats matters more than hitting the minimum once.
Damping and the grade choice
One reason machine tool builders stay with gray iron is its graphite, which soaks up vibration. Higher grades are not automatically better dampers; the graphite network and the casting's ribbing do most of that work. A supplier who talks only about tensile strength and never about damping is missing the main reason you chose cast iron in the first place.
Specifying grade to a supplier
Put the grade, the test standard and any hardness band on the drawing, and say which faces must be free of chill. Tell the foundry the service loads if you can, because they may suggest a grade you had not considered. Clear specs prevent the quiet grade substitution that happens when a manufacturer is left to guess.
Common grade mistakes
The usual errors are over-specifying strength to feel safe, forgetting that hardness hurts machinability, and assuming the number alone guarantees quality. Another is mixing grades in one assembly without reason, which complicates melting and invites confusion on the floor. Keep it simple and justified.
Grade and what happens on the foundry floor
Grade also shapes welding and later repair. HT200 and HT250 weld and braze with reasonable care, while HT300 demands stricter preheat because its higher strength brings more brittle behaviour in the heat-affected zone. If a casting will be repaired in service, say so when you order, because a repairable grade chosen at the design stage beats a stronger grade that cracks the moment someone strikes an arc on it. The foundry can also trim the phosphorus and adjust alloy content to make welding easier without dropping the grade much, which is the kind of quiet compromise a good manufacturer suggests once they know the part's whole life rather than just its first pour. Melt control is where grade is actually won or lost, so ask how the supplier verifies each heat instead of assuming the certificate speaks for itself.
A short selection checklist
Ask whether the part carries load or just shape, how it will be machined, and what accuracy depends on it. Most frames land on HT200 or HT250; most structural beds land on HT250 or HT300. Confirm the test standard with your supplier, keep the paperwork, and you will have chosen the grade for the right reasons rather than the loudest ones.
References
ASTM A48/A48M, Standard Specification for Gray Iron Castings.
ISO 185:2020, Grey cast iron - Classification.
ASM Handbook, Volume 1: Properties and Selection of Irons, Steels, and High-Performance Alloys, ASM International.
Kalpakjian, S., Manufacturing Engineering and Technology, Pearson.
Campbell, J., Complete Casting Handbook, 2nd edition, Butterworth-Heinemann.
About the Author
Written by Priya Nandakumar. Priya Nandakumar works in materials engineering at a casting manufacturer and helps customers specify the right iron grade for structural machine components.
